Thrusterpedia

Which boat thruster, what it costs, how to get it installed

We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.

Owning one · upkeep

Bow thruster repair cost: the part, the yard, and when a new unit wins

Most thruster repairs are a part under a few hundred dollars. The bill is the finding out, and whether the boat has to come out of the water to reach it. This page prices each job from US dealers' listings, gives the yard's rate, and lists what 9 owners paid or were quoted.

For your own boat: the Thruster Finder asks seven to nine questions and lists what fits her, priced installed; the size calculator gives her thrust figure from her length and kind; the quote checker says where a yard’s number sits against what owners paid. The compare page puts every model in one table, sorted or side by side.

  • Every part price from a dealer’s listing, dated
  • Yard rates from published rate cards
  • Owner figures are hearsay, labeled
  • An anode or a drive pin $2 to $138 › The part alone, from US dealers.
  • A propeller $37 to $351 › By bore and maker, 55 listings on file.
  • A whole motor $313 to $5,257 › The motor alone, from US dealers. Owners report rebuilds from $750.
  • Yard labor $160 to $180 › An hour, from published skilled-trade rates. The hours are the yard’s to quote.
  • A day out of the water $510 to $900 › A 35 ft boat on eight yards’ rate cards, lifted and back in a day.
  • Owner repair figures on file 9 › 2012 to 2026, newest first, each linked to its post.

Prices are in US dollars, from US dealers and US yards. Outside the US, shipping, import duty and your local yard’s rates are not included.

The short answer: five steps before you pay anyone

  1. Find the fault before you price the fix. A click and no run, one direction only, a motor that runs and a boat that does not move: each points at a different part, and most of them are cheap. What to check, in order
  2. Price the part on this site. Every product page carries a parts card with the US dealer number, the maker’s number and the price, read from the dealer’s listing on a stated date. Not sure which model you have? Find out first. Find your model
  3. Work out whether the boat has to come out. The anode, the pin, the propeller, the gear leg and its seals sit in the water. A diver reaches the first three on most units. A leg means the hard. What a day out costs
  4. Then add the yard’s hours at $160 to $180. No maker publishes how long a repair takes, so ask the yard for the hours in writing before the boat is lifted. The yard’s rate

What each repair costs, by job

The part prices are this site’s parts file: 391 parts with a US dealer price, out of 692 the 6 makers list for these jobs, each price read from the dealer’s own page on a stated date. They are the prices the product pages print. The range is the cheapest listing to the dearest across every maker and size, so your own part sits somewhere inside it.

Each repair: what you notice, who does it, and the part from US dealers
JobWhat you noticeWho does itThe part, on fileBoat out?Check first
Anode Found half gone or missing at a haul-out, or by your diver. A diver in the water, or you on the hard. Minutes. $9 to $138 34 of 45 parts priced, 6 makers Yes, or a diver The anode page
Shear pin or drive pin The motor runs and the boat does not move. You, on the hard or with the motor off where the pin sits inside. Some units need a diver. $2 to $67 16 of 24 parts priced, 4 makers Yes, or a diver The shear pin page
Propeller A chipped or bent blade: noise, vibration, less push than it had. You on the hard, or a diver for a nut-on propeller. The pin and anode come off with it. $37 to $351 55 of 72 parts priced, 5 makers Yes, or a diver The noise page
Gear leg (tailpiece) Oil in the tunnel, a grinding noise, or a leg that will not turn by hand. A yard, on the hard. The motor comes off from inside and the leg drops out of the tunnel. $68 to $5,200 42 of 54 parts priced, 3 makers Yes The noise page
Seals and gaskets Oil weeping at the tunnel, or water in the gear oil. A yard, on the hard, usually with the leg out. $2 to $135 20 of 56 parts priced, 4 makers Yes The maintenance page
Motor brushes It clicks and runs weakly, or runs only after a tap on the motor. You with the motor off the leg, or a motor shop. Inside the boat. $37 to $353 15 of 37 parts priced, 3 makers No The not-working page
Solenoid or relay (the motor switch) A click at the bow and nothing else, or one direction only. You or a marine electrician. Inside the boat, with her afloat. $144 to $1,091 30 of 61 parts priced, 4 makers No The not-working page
Controller (the electronics box) Nothing from the panel, a fault code, or a unit that stops and starts. A marine electrician, or you with the maker’s codes. Inside the boat. $161 to $2,151 8 of 40 parts priced, 4 makers No The light and beep codes
Control panel, joystick or remote Dead buttons at one helm while the other works, or a remote that will not pair. You, at the helm. Inside the boat. $198 to $1,000 23 of 25 parts priced, 6 makers No The not-working page
Main fuse Nothing at all, after a long run or a jam. You. A cheap fix, once you know why it blew. $14 to $51 103 of 112 parts priced, 5 makers No The not-working page
Whole motor Burnt smell, a motor that will not turn, or one a shop will not rebuild. A yard or a motor shop; you can unbolt it. Inside the boat on a tunnel unit, in the water on an external one. $313 to $5,257 45 of 138 parts priced, 5 makers No The not-working page

Part prices from US dealers’ listings (Defender, Fisheries Supply, MAURIPRO, Marinedeal, Seatech Marine, West Marine, Imtra, Quick USA and the makers’ own stores), read 24 Oct 2026 to 14 Nov 2026 and refreshed weekly; each product page’s parts card links the listing a price came from. “Boat out?” says where the part sits. An external unit that lifts out of the water puts its propeller and anode in reach from the dock.

The cheapest drive pin on file

Max Power’s propeller pin, $2 at MAURIPRO. A pin is made to break so the drive does not.

The dearest motor on file

Max Power’s replacement motor, $5,257 at MAURIPRO. Less than a new unit of the model it fits.

Motor brushes

Brushes run $37 to $353 on US listings, depending on the motor. One owner paid about $166 for the maker’s set. A motor shop matches them from a starter catalog for far less.

The yard: the rate, the hours and the lift

The rate: $160 to $180 an hour

That is the skilled-trade rate this site uses for every install estimate, inside the published rate rows on the cost page. A marine electrician for the wiring side sits in the same range.

No maker publishes repair hours. The manuals give an install time and a service list, never how long a motor swap or a leg takes. Ask your yard for the hours in writing. A motor comes off a tunnel unit on four bolts from inside the boat; a gear leg drops out of the tunnel once the motor is off, with the boat on the hard.

A day out of the water: $510 to $900

A 35 ft boat lifted, washed and blocked where the yard bills it, and one lay day, worked on the same eight rate cards the install pages use (read 30 September 2026). The install’s 5 to 7 days on the hard come to $620 to $1,690 on the same cards. A yard that lifts and relaunches in the slings may bill less than a day.

A diver is the cheaper route where the part allows it. Two owners reported in May 2025 that their diver fits an anode they supply for $10 on top of a cleaning visit. Another was quoted $200 for a diver against $480 for a short haul. A boat that lives on a trailer pays for neither.

The part is rarely the bill. One owner’s gear-leg hub was about $200. The haul-out, two months of blocking while a warranty claim went unanswered, the inspection and the labor were his. If the boat has to come out, have the part in hand before the lift.

What owners paid, or were quoted

These are forum posts and an owners’ group, read on the dates given, each linked. Each is what one owner reported. This site has not checked the figures, and the older ones predate today’s yard rates. They cover the motor, the solenoid, the brushes, the panel, the anode and the gear leg. No owner figure is on file yet for the shear pin, the propeller, the seals, the controller and the fuse.

Owner-reported repair figures, newest first
PostedBoat and unitWhat the figure coversFigureBasisNote
September 2026 Linssen 32, VETUS tunnel unit A new solenoid, owner installed $250 Paid It did not fix the fault. The maker quoted $450 for brushes, which is why the motor went to a shop twice.
May 2025 36 ft trawler, San Diego, and a 65 ft motor yacht A diver fits an anode you supply $10 Paid On top of the diver’s cleaning visit: $65 a cleaning on the 36 footer, $178 on the 65.
December 2024 20-year-old Side-Power Two helm joysticks, owner installed $300 Paid Older three-wire joysticks in place of the touchpads, both stations for under this figure.
November 2024 50 ft trawler conversion, VETUS 95 kgf Motor rebuilt by an alternator shop No figure Paid New bearings, brushes, relays and some machining, in Canada, for about half the price of a new motor. No dollar figure given.
January 2023 Pacific Trawler 40, a 21-year-old 147 lb unit The next model’s motor, bolted on $1,100 Quoted About $3,500 for the bigger unit if he did it himself, with one more battery.
January 2022 VETUS 55 kgf, Norway A brush set $166 The part alone The maker’s BSX34 set. He bought Bosch starter brushes of the same size for about twenty pounds instead.
August 2021 Beneteau 37, Baltimore A diver against a short haul, for a propeller anode $200 to $480 Quoted The diver at the low figure, the haul at the high one. A propeller anode, not a thruster’s, but the same choice.
March 2021 Albin 28 TE, VETUS BOW5012 Motor overhaul: bearings and brushes, quoted three ways $750 to $2,000 Quoted Two VETUS service shops in Fort Lauderdale at $2,000 (two hours off, two on, at $125 an hour, plus $1,500 in parts) and about $1,000; an auto electric shop at $750 to $800. A dealer offered a whole new BOW6012 at $2,050.
August 2020 Ranger Tug 27 (2019), Lewmar A gear-leg hub assembly $200 The part alone The part. The haul-out, two months of blocking, the inspection and the labor were his own bill while a warranty claim went unanswered.
July 2012 Side-Power, Massachusetts Motor rebuilt by an auto electric shop $195old Paid The maker wanted $1,200 for a new motor and said this one was not worth rebuilding.

Read 1 and 2 November 2026. “Paid” is a bill the owner says was paid; “Quoted” a price offered; “The part alone” a part bought with the labor still to come. “Old” marks a figure from before yard labor roughly doubled between 2021 and 2025. If you have a repair bill, send it in and it goes on this table, credited by first name or not at all.

Repair it, or replace the unit?

A new motor

$313 to $5,257 on file; one owner was quoted $1,100 for the next model up, bolted to his old leg. On a tunnel unit it goes on from inside the boat, with her afloat. At most 73 percent of a new unit of the same model, hardware alone.

A motor rebuild

Quoted or paid at $750 to $2,000: bearings, brushes and sometimes the relays, at an auto electric or alternator shop. Back in 2012 one maker said a motor was not worth rebuilding; a local shop rebuilt it for $195.

A new tunnel unit, installed

$10,300 to $14,000 typical on a 35 to 40 ft boat, the hardware alone $2,200 to $3,900. An external unit installed runs $4,540 to $16,472 on the same row.

The arithmetic favors the repair almost every time. Each of the 40 motor prices on this site’s file costs less than a new unit of the model it fits, at most 73 percent of it. A new unit also needs the yard to put it in.

Two things change that. The first is a model nobody makes any more: one owner found his motor out of production and the newer motors a different fit, so the choice was a rebuild or a new thruster, tunnel work included. The second is a tunnel unit that is undersized for the boat, where the fault is the excuse to size it right. The size calculator tells you which you have.

An external unit is the other case. Its motor sits in the water, so a flooded motor is a new motor, and the new one bolts onto the same mount with the boat afloat. The stern thruster cost page prices every external unit installed, and the main cost page every tunnel by boat length.

Keep it cheap: the three habits

Blip it, never hold it

Every maker prints a run limit, and a burnt motor is the repair that costs most. The run time page has each maker’s figure.

Feed it the right voltage

Low voltage at the motor cooks brushes and solenoids. The battery close to the thruster and the cable the maker asks for; the wiring calculator checks yours.

Change the anode at half

The cheapest part on the boat protects the dearest one in the water. The maintenance page puts every maker’s yearly list side by side.

One owner’s solenoid, replaced at $250 on a yard’s say-so, did not fix the fault, and the motor went to a shop twice. That is the other half of keeping it cheap: find the fault before you buy the part. The not-working page runs the checks in order, and its light and beep codes cover every maker that prints them.

Where to go next

More in this section: Bow and stern thruster parts Bow thruster anodes

The prices on this page are estimates for planning, read from dealers and yards on the dates given. They are not a quote for your boat. Check any part and any price against the maker’s manual and your yard before you buy or install anything. The full wording is in our terms.