We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.
Quick · tunnel thruster · bow
Quick BTQ 300: specs, price and the boats it fits
It gives 551 to 595 lb of push, across two sizes. Quick sells it for boats of 65 to 99 ft. It runs on 24 V.
- Haul-out to install
- DIY 1 of 5: yard job
- 3-year warranty
Choose a size
The Quick BTQ 300 comes in two sizes. Each has its own price, wiring and boats it suits. Pick one and the page below shows that size.
Every size side by side
| Size | Push | Voltage | Quick’s boat length | Price |
|---|---|---|---|---|
| BTQ 300-250 | 551 lb (250 kgf) | 24 V | 65 to 85 ft | $11,962 |
| BTQ 300-270 | 595 lb (270 kgf) | 24 V | 75 to 99 ft | $13,631 |
From the database. The figures are Quick’s and the dealers’.
Quick stats
- Thrust 551 lb 250 kgf, Quick's rating
- Boat length 65 to 85 ft Quick's own range
- Price per lb of thrust $21.71 Unit only. $40 to $59 installed
- Voltage 24 V As sold
- Battery at 24 V 800 CCA and 150 Ah Two batteries, near the thruster
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
- To install it Haul-out The boat comes out of the water
- Anodes $166.91 A change. More than twice another maker's
Quick stats
- Thrust 595 lb 270 kgf, Quick's rating
- Boat length 75 to 99 ft Quick's own range
- Price per lb of thrust $22.91 Unit only. $43 to $62 installed
- Voltage 24 V As sold
- Battery at 24 V 500 CCA and 125 Ah Four batteries, near the thruster
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
- To install it Haul-out The boat comes out of the water
- Anodes $166.91 A change. More than twice another maker's
About the Quick BTQ 300
The BTQ 300 is the largest bow thruster Quick sells in the US, made for yachts of about 65 to 99 ft. Two propellers in a big tube through the hull give about 551 or 595 lb of push on 24 V. Quick also lists a still larger 48 V model. It comes from a maker in the thruster business since 2007.
It starts at $11,962 at Quick’s US store, for the thruster alone. The control panel, tube and fuse come separately: Quick’s joystick is $540, the tube starts at $1,247 and the heavy-duty fuse holder is $209. Batteries, cable and charging add about $2,322 to $4,767 more. See below for the full list.
Read more
The drive coupling for this size is the priciest in the range, $607 at the store, and the motor brushes are the other part that wears. Quick calls the unit unsuited to continuous running, so the panel turns it off once a run nears 5 minutes 40 seconds, then rests it for 20 minutes. Quick asks for a yearly strip-down, and its three-year warranty is void if anyone it hasn’t authorized does that work.
Installers will find the wiring figures and dimensions further down. For the rest of Quick’s line, read the Quick thruster review.
Where this summary comes from (10 sources, read 11 October 2026)
- Quick USA store product page
- Quick BTQ 250/300 installation manual, REV006C
- Boating Industry Canada, 18 May 2023: Quick thruster production began in 2007
- Quick BTQ Series installation manual, REV005A (July 2025)
- Quick TCD 2022/2042 control panel manual, REV001a
- Quick USA store: thrusters, panels, tubes, fuses and spares
- Quick USA: conditions of warranty
- myHanse, Jul 2016: brushes, relay and a six-month parts wait
- myHanse, Aug 2016: thruster stops after hard use in a crosswind
- myHanse, Jun 2022: Quick stern thruster, brushes and the overheat lockout
Will the Quick BTQ 300 steer your boat?
80 FT TRAWLER · BOW · 15 KT WIND
Every knot figure here is wind speed, not boat speed or current.
On a 80 ft trawler the Quick BTQ 300 (551 lb) steers her in a 17 knot breeze. Her bow needs about 428 lb from a tunnel to steer her in a 15 knot breeze.
The finder lists it for her.
The Quick BTQ 300 on a trawler, by length
- 25 ft54 kt
- 30 ft45 kt
- 35 ft39 kt
- 40 ft34 kt
- 45 ft30 kt
- 50 ft27 kt
- 55 ft25 kt
- 60 ft23 kt
- 65 ft21 kt
- 70 ft19 kt
- 75 ft18 kt
- 80 ft17 kt
Outlined: the finder does not list it at that length (under 13 kt, far more than she needs, or outside Quick’s own length range).
- Under 10 kt
- 10 to 15 kt
- 15 to 20 kt: the sweet spot
- Over 20 kt: more than she needs
Prices are the low end of the installed total, from our estimate. For your own boat, drive and installer, the finder prices each unit.
Is it right for your boat?
Every kind of boat it fits, by length
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 65 to 80 ft | None |
| Houseboat | 59 to 70 ft | 71 to 80 ftfull thrust to about 13 knots at 80 ft |
| Catamaran | 74 to 80 ft | None |
| Trawler | 65 to 80 ft | None |
| Motor yacht | 65 to 80 ft | None |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | No length. More thrust than the boat needs. | |
| Center console | No length. More thrust than the boat needs. | |
The Quick BTQ 300 against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.
The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit steers her in a 13 or 14 knot wind, within 15 percent of the 15 knot breeze this site sizes for. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
How we size it
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 70 ft, and a sailboat to 80 ft. The maker gives one range for every boat.
The table tries the Quick BTQ 300 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 59 ft, just past Quick’s own range (65 to 85 ft).
It is sized for five kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the installing. The compare page sets this unit beside others.
What it costs installed
A yard job, everything in. Our estimate.
| Boat | Total installed |
|---|---|
| 59 ft | $21,733 to $31,998$39 to $58 a lb of thrust |
| 70 ft | $21,923 to $32,528$40 to $59 a lb of thrust |
| 80 ft | $22,083 to $33,008$40 to $60 a lb of thrust |
From the shortest to the longest boat it is sized for.
What is in each total
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $1,140 to $3,860 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts |
|---|---|---|---|---|---|
| 59 ft | $11,962 | $5,120 to $12,60032 to 70 hours | $1,140 to $2,850 | $2,322 to $2,456 | $1,189 to $2,130 |
| 70 ft | $11,962 | $5,120 to $12,60032 to 70 hours | $1,330 to $3,380 | $2,322 to $2,456 | $1,189 to $2,130 |
| 80 ft | $11,962 | $5,120 to $12,60032 to 70 hours | $1,490 to $3,860 | $2,322 to $2,456 | $1,189 to $2,130 |
For every length in the table above.
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 26 October 2026.
- At 24 V: two 12 V batteries in series, at least 800 CCA and 150 Ah each (Quick’s minimum), $1,996 for both; Quick’s cable table gives 3/0 to 2 x 1/0 AWG, priced on 4/0 AWG, the nearest size cut to length: $180 to $314 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
DIY breakdown
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You install it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 hours Electrician: in the yard’s hours Plus a haul-out.
Every step, and who does it
- The whole job: hull, unit and wiring Yard 32 to 70 hours The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Will the Quick BTQ 300 steer your boat?
80 FT TRAWLER · BOW · 15 KT WIND
Every knot figure here is wind speed, not boat speed or current.
On a 80 ft trawler the Quick BTQ 300 (595 lb) steers her in an 18 knot breeze. Her bow needs about 428 lb from a tunnel to steer her in a 15 knot breeze.
The finder leaves it off her list. It shows the BTQ 300-250 for her instead.
The Quick BTQ 300 on a trawler, by length
- 25 ft56 kt
- 30 ft47 kt
- 35 ft40 kt
- 40 ft36 kt
- 45 ft31 kt
- 50 ft28 kt
- 55 ft26 kt
- 60 ft24 kt
- 65 ft22 kt
- 70 ft20 kt
- 75 ft19 kt
- 80 ft18 kt
Outlined: the finder does not list it at that length (under 13 kt, far more than she needs, or outside Quick’s own length range).
- Under 10 kt
- 10 to 15 kt
- 15 to 20 kt: the sweet spot
- Over 20 kt: more than she needs
Prices are the low end of the installed total, from our estimate. For your own boat, drive and installer, the finder prices each unit.
Is it right for your boat?
Every kind of boat it fits, by length
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 68 to 80 ft | None |
| Houseboat | 68 to 73 ft | 74 to 80 ftfull thrust to about 13 knots at 80 ft |
| Catamaran | 77 to 80 ft | None |
| Trawler | 68 to 80 ft | None |
| Motor yacht | 68 to 80 ft | None |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | No length. More thrust than the boat needs. | |
| Center console | No length. More thrust than the boat needs. | |
The Quick BTQ 300 against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.
The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit steers her in a 13 or 14 knot wind, within 15 percent of the 15 knot breeze this site sizes for. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
How we size it
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 73 ft, and a sailboat to 80 ft. The maker gives one range for every boat.
The table tries the Quick BTQ 300 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 68 ft, just past Quick’s own range (75 to 99 ft).
It is sized for five kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the installing. The compare page sets this unit beside others.
What it costs installed
A yard job, everything in. Our estimate.
| Boat | Total installed |
|---|---|
| 68 ft | $25,548 to $36,408$43 to $61 a lb of thrust |
| 75 ft | $25,668 to $36,748$43 to $62 a lb of thrust |
| 80 ft | $25,748 to $36,988$43 to $62 a lb of thrust |
From the shortest to the longest boat it is sized for.
What is in each total
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $1,290 to $3,860 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts |
|---|---|---|---|---|---|
| 68 ft | $13,631 | $5,120 to $12,60032 to 70 hours | $1,290 to $3,280 | $4,318 to $4,767 | $1,189 to $2,130 |
| 75 ft | $13,631 | $5,120 to $12,60032 to 70 hours | $1,410 to $3,620 | $4,318 to $4,767 | $1,189 to $2,130 |
| 80 ft | $13,631 | $5,120 to $12,60032 to 70 hours | $1,490 to $3,860 | $4,318 to $4,767 | $1,189 to $2,130 |
For every length in the table above.
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 26 October 2026.
- At 24 V: four 12 V batteries, two strings of two in series, at least 500 CCA and 125 Ah each (Quick’s minimum), $3,992 for all four; Quick’s cable table gives 4/0 to 2 x 4/0 AWG: $180 to $629 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
DIY breakdown
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You install it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 hours Electrician: in the yard’s hours Plus a haul-out.
Every step, and who does it
- The whole job: hull, unit and wiring Yard 32 to 70 hours The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Related videos
One of Quick’s own videos, from its YouTube channel. They play only when you tap. A maker’s video is its pitch, so take any claim back to the figures on this page.
Know before you buy
What sets this model apart, what it costs to keep, and what to weigh.
Price per pound of thrust
$21.71 a lb The unit’s price over its published thrust, on the smallest size. The bars are Quick’s next sizes and the nearest other makers.Controls
The thruster, a drilling template, gasket and O-ring. The TCD panel and the fuse holder are bought.
- Quick FNTCD2022000A00, no US price found.
- Quick FNTCDEX06000A00, FNTCDEX08000A00, no US price found.
Pricey wear part: anodes
$166.91 a change- Anode (FVSGANBTQ30AA00): $166.91 at Quick USA.
A change costs $166.91. That is nearly five times the $33.75 for Sleipner’s anode on the same 300 mm tunnel (SM201180A, Defender). An anode is a plain block of metal that wears away by design, so you will buy it again.
They sit below the waterline, so a change means a haul-out or a diver.
Service and warranty
Quick gives at least 3 years from purchase, with repair or replacement at Quick's discretion. It is void if maintenance is done by anyone Quick has not authorized, or with parts that are not original. Removal and reinstalling are at your cost.
See Quick’s warranty Quick USA's conditions of warranty.Special mentions
Battery: at 24 V it wants two batteries of 800 CCA and 150 Ah or more, Quick's figure. The cheapest that meets it is the Odyssey Extreme PC1800-FT start / deep cycle, $998.12.
Charger: a NOCO GEN5X2 two-bank shore charger, $146.41. It is the one our estimate prices.
Dealer prices at Fisheries Supply, read 26 October 2026.What to weigh
The boat comes out of the water to install it: it needs a tunnel bore below the waterline.
Parts for the Quick BTQ 300
See the Quick BTQ 300 manualThe US dealer number comes first, then Quick’s own. Prices are each dealer’s on the day shown, before shipping and tax. Check the plate on your motor before you order: some parts change with the tunnel size, the voltage or the year.
For the install what the box leaves you to buy
The manual button above opens it on the maker's site. It has the hull, wiring and fuse figures for this model.
From Quick’s BTQ Series installation manual REV 005A and the TCD control manual, September 2025, read 30 September 2026.
- In the box
- The thruster with its reversing contactor and anode, a drilling template, gasket, O-ring, the manual.
- Bought separately
- "Recommended Quick accessories not included": the TCD control panels, the line switch, the THF fuse holder. Plus the fuse, the cable, a battery disconnection switch, a 4 A control fuse and switch, the tube.
- Charging
- The manual gives a battery table by model, in amp-hours and cold cranking amps, and a diagram with the panel on the service battery. It says nothing about how the thruster bank is charged.
The manual’s words, page 10: “Standard supply and material included in the package: Thruster, Drilling template, Gasket, O-ring, Installation and use manual, Conditions of warranty.”
The “other parts” line in the estimate above covers these parts as a range, $1,189 to $2,130 at Fisheries Supply’s prices on 30 September 2026 and 26 October 2026, because the exact items depend on your boat. The batteries, cable and charger have a line of their own. The cost page has what every maker says about each part.
Tunnel tube
Fisheries Supply lists it as “Sleipner fiberglass tunnel tube, 300 mm bore, 1000 mm”.
Sold in lengths from about 39 to 59 in. This is the shortest: the yard cuts the tube to the width of your hull at the thruster. No Quick tube is listed at this bore. This one is another maker's.
Control panel
Ask for Quick FNTCD2022000A00.
Not sold at Fisheries Supply. Ask a Quick dealer.
Control cable, panel to thruster
Ask for Quick FNTCDEX06000A00, FNTCDEX08000A00.
Not sold at Fisheries Supply. Ask the panel dealer.
Main fuse
Ask for 400 A CNL DIN fuse. This one is for the BTQ 300-250, 250 KGF, double propeller, 24 V version.
Quick's figure for the BTQ 3025024 (BTQ manual, REV005A). Quick lists its TFH holders for it. Not listed at Fisheries Supply; ask a Quick dealer.
Main fuse
Ask for 500 A CNL DIN fuse. This one is for the BTQ 300-270, 270 KGF, double propeller, 24 V version.
Quick's figure for the BTQ 3027024 (BTQ manual, REV005A). Quick lists its TFH holders for it. Not listed at Fisheries Supply; ask a Quick dealer.
Fuse holder
Ask for Quick TFH fuse holder for the CNL fuse.
Ask the dealer who sells the fuse.
Battery switch
Fisheries Supply lists it as “HD-Series 600 A battery switch, on/off”. This one is for the BTQ 300-250, 250 KGF, double propeller, 24 V version.
Rated at or above the 400 A main fuse. If your manual names its own switch, use that one.
Battery switch
Fisheries Supply lists it as “HD-Series 600 A battery switch, on/off”. This one is for the BTQ 300-270, 270 KGF, double propeller, 24 V version.
Rated at or above the 500 A main fuse. If your manual names its own switch, use that one.
Control-circuit fuse holder
Fisheries Supply lists it as “Waterproof in-line ATO/ATC fuse holder”.
The maker asks for a 4 A fast-blow fuse on the control supply, with a switch.
Batteries
Ask for 2 at 800 CCA and 150 Ah or more, in series for 24 V. This one is for the BTQ 300-250, 250 KGF, double propeller, 24 V version.
You need 2. No listing at Fisheries Supply meets this in stock.
Batteries
Ask for 4 at 500 CCA and 125 Ah or more, 2 in series for 24 V, 2 such strings in parallel. This one is for the BTQ 300-270, 270 KGF, double propeller, 24 V version.
You need 4. No listing at Fisheries Supply meets this in stock.
Battery cable, red and black
Defender lists it as “Ancor tinned battery cable 4/0 AWG, cut to length, red or black”. This one is for the BTQ 300-250, 250 KGF, double propeller, 24 V version.
You need 10 ft of each color. For about 20 ft of cable in all, out and back. Measure your run and check it against the cable table in the manual: never go smaller than it asks for.
Battery cable, red and black
Defender lists it as “Ancor tinned battery cable 4/0 AWG, cut to length, red or black”. This one is for the BTQ 300-270, 270 KGF, double propeller, 24 V version.
This is the short run. A longer run takes heavier cable: the wiring calculator sizes yours. You need 5 ft of each color. For about 10 ft of cable in all, out and back. Measure your run and check it against the cable table in the manual: never go smaller than it asks for.
Cable lugs
Fisheries Supply lists it as “Tin-plated starter lugs, 4/0 AWG, bag of 10”. This one is for the BTQ 300-250, 250 KGF, double propeller, 24 V version.
The listing runs $47.52 to $49.44 by stud size. Eight ends on one run, with two spare.
Cable lugs
Fisheries Supply lists it as “Tin-plated starter lugs, 4/0 AWG, bag of 10”. This one is for the BTQ 300-270, 270 KGF, double propeller, 24 V version.
This is the short run. A longer run takes heavier cable: the wiring calculator sizes yours. The listing runs $47.52 to $49.44 by stud size. Eight ends on one run, with two spare.
Charger
Fisheries Supply lists it as “GEN5X2 on-board charger, 10 A, 2 banks”.
Or a DC-to-DC charger from the house system: ask the electrician.
Outside the hull replacement parts in the water
Anode
The metal that wears away in the water so the drive does not. Quick calls it “BTQ Anodes, Model 300”.
Read on Quick USA, Quick's own US store; Quick's manual site could not be opened.
Propeller, left hand
The propeller on the drive. Quick calls it “Propellers, Model BTQ/BTR 300, Prop Side Left”.
Read on Quick USA, Quick's own US store; Quick's manual site could not be opened. Double propeller: one right and one left.
Propeller, right hand
The propeller on the drive. Quick calls it “Propellers, Model BTQ/BTR 300, Prop Side Right”.
Read on Quick USA, Quick's own US store; Quick's manual site could not be opened. Double propeller: one right and one left.
Inside the boat replacement parts on board
Main fuse
The main fuse at the battery, in the rating the maker gives. Quick calls it “Bow Thruster Fuse, 275 Amp”. It fits the BTQ 300-250, 250 KGF, double propeller, 24V size on this page.
The 275 A rating is on Quick USA's page for this model; Quick sells that fuse as FVEFF275CNLDA00. The page calls for two (2 x 275 A).
Main fuse
The main fuse at the battery, in the rating the maker gives. Quick calls it “Bow Thruster Fuse, 325 Amp”. It fits the BTQ 300-270, 270 KGF, double propeller, 24V size on this page.
The 325 A rating is on Quick USA's page for this model; Quick sells that fuse as FVEFF325CNLDA00. The page calls for two (2 x 325 A).
Control panel, on/off dual joystick (bow and stern)
The control at the helm. Quick calls it “TCD 2044 thruster double joystick controller”.
Runs a bow and a stern thruster.
Control panel, on/off push buttons
The control at the helm. Quick calls it “TCD 2022 thruster controller”.
Its manual holds the run limit.
Control panel, on/off single joystick
The control at the helm. Quick calls it “TCD 2042 thruster joystick control”.
Motor coupling kit
The electric motor that turns the propeller. Quick calls it “Quick OSP Coupling Kit, BTQ300”.
Read on Quick USA, Quick's own US store; Quick's manual site could not be opened. The coupling joins the motor to the drive.
No part matches. Try the number without spaces, or the part’s name.
The install parts are matched to Quick’s own figures and priced at Fisheries Supply, with the battery cable at Defender, cut to length.
Spare part numbers come from Quick’s parts pages and manuals. A dealer may sell a part we have not priced. Search for the number.
Other sizes and close alternatives
- Size down Quick BTQ 250 four sizes, 265 to 529 lb · $8,624 to $10,571
- Other maker Lewmar 300TT GEN 2 two sizes, 550 to 616 lb · $7,339 to $10,499
- Other maker VETUS Bow 285 628 lb · $8,357
- Other maker Max Power CT225 (composite leg) 551 lb · $3,991
The other makers listed are the nearest match each makes, of the same style and for the same end, within a quarter of its thrust. The compare page lists every model, and the thruster index lists every model with a page here.
For the yard and the installer
Every published figure, with its source.
Full spec sheet
| Thrust and motor | |
|---|---|
| Thrust | 551 lb (250 kgf) As printed: 250 Kgf (551 lb) |
| Motor | 10 kW |
| Voltage | 24 V |
| Run limit | Not published |
| Installation | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 300 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to install it | Yes |
| Maker’s boat length | 65 to 85 ft |
| Price and ordering | |
| Price | $11,962 equipment only, the maker's own price, quickusastore.com, 26 October 2026 |
| Part number | FGBT30250240T00BTQ 300-250, 250 KGF, double propeller, 24 V FGBT30270240T00BTQ 300-270, 270 KGF, double propeller, 24 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| The site’s review | Quick thruster review |
Every published figure the site holds for the Quick BTQ 300, with where each came from.
The tunnel: length and depth rules
Tunnel length. The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual.
Depth below the waterline. In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C.
Our notes from the manual and listings
In the box: The thruster, a drilling template, gasket and O-ring. The TCD panel and the fuse holder are bought.
BTQ 300-250, 250 KGF, double propeller, 24 V
The 250 kgf version, 24 V, with twin counter-rotating propellers in a 300 mm tunnel. The category page puts the whole BTQ 300 series on boats of 62 to 98 ft. The band here is the US store's own figure for this version. The manual gives a 400 A fuse at 24 V and a weight of 46.7 kg.
Its cable is 2/0 for a total run under 5 m (positive plus negative), two 1 AWG per leg to 10 m, two 3/0 AWG per leg to 20 m. The US store page printed 77.2 lb for both BTQ 300 variants where the manual gives 46.7 kg for this one and 55.9 for the 270.
The manual prints a fuse and cable sizes but no current draw and no battery figure. No product page gives a run time. The installation manual says the unit is not designed for continuous use and leaves the limit to the control panel. The panel's own manual cuts the command after about five minutes and resets it after a cool-down the panel computes.
The tunnel sits at least three quarters of its diameter below the waterline. Once a year the unit comes apart for inspection, anode included. The warranty runs three years from purchase, with repair or replacement at Quick's discretion. The warranty is void for maintenance by anyone Quick has not authorized or for non-original parts. Removal and reinstalling are at your cost.
Quick announced a brushless QSY range in September 2026, rated for ten minutes' continuous running. The QSY range will sit beside this brushed line. The price is Quick's US store's own for this size at 24 V, read 12 October.
BTQ 300-270, 270 KGF, double propeller, 24 V
The 270 kgf BTQ 300, twin counter-rotating propellers, 24 V. The manual gives a 500 A fuse at 24 V and a weight of 55.9 kg. Its cable is 3/0 for a total run under 5 m (positive plus negative), two 3/0 AWG per leg to 10 m, two 4/0 AWG per leg to 20 m. The manual's ladder tops out above it with a 48 V 300 kgf unit that no US page lists.
Where each point above comes from
- The boat comes out of the water to install it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it
For the yard and the installer
Every published figure, with its source.
Full spec sheet
| Thrust and motor | |
|---|---|
| Thrust | 595 lb (270 kgf) As printed: 270 Kgf (595 lb) |
| Motor | 12 kW |
| Voltage | 24 V |
| Run limit | Not published |
| Installation | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 300 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to install it | Yes |
| Maker’s boat length | 75 to 99 ft |
| Price and ordering | |
| Price | $13,631 equipment only, the maker's own price, quickusastore.com, 26 October 2026 |
| Part number | FGBT30250240T00BTQ 300-250, 250 KGF, double propeller, 24 V FGBT30270240T00BTQ 300-270, 270 KGF, double propeller, 24 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| The site’s review | Quick thruster review |
Every published figure the site holds for the Quick BTQ 300, with where each came from.
The tunnel: length and depth rules
Tunnel length. The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual.
Depth below the waterline. In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C.
Our notes from the manual and listings
In the box: The thruster, a drilling template, gasket and O-ring. The TCD panel and the fuse holder are bought.
BTQ 300-250, 250 KGF, double propeller, 24 V
The 250 kgf version, 24 V, with twin counter-rotating propellers in a 300 mm tunnel. The category page puts the whole BTQ 300 series on boats of 62 to 98 ft. The band here is the US store's own figure for this version. The manual gives a 400 A fuse at 24 V and a weight of 46.7 kg.
Its cable is 2/0 for a total run under 5 m (positive plus negative), two 1 AWG per leg to 10 m, two 3/0 AWG per leg to 20 m. The US store page printed 77.2 lb for both BTQ 300 variants where the manual gives 46.7 kg for this one and 55.9 for the 270.
The manual prints a fuse and cable sizes but no current draw and no battery figure. No product page gives a run time. The installation manual says the unit is not designed for continuous use and leaves the limit to the control panel. The panel's own manual cuts the command after about five minutes and resets it after a cool-down the panel computes.
The tunnel sits at least three quarters of its diameter below the waterline. Once a year the unit comes apart for inspection, anode included. The warranty runs three years from purchase, with repair or replacement at Quick's discretion. The warranty is void for maintenance by anyone Quick has not authorized or for non-original parts. Removal and reinstalling are at your cost.
Quick announced a brushless QSY range in September 2026, rated for ten minutes' continuous running. The QSY range will sit beside this brushed line. The price is Quick's US store's own for this size at 24 V, read 12 October.
BTQ 300-270, 270 KGF, double propeller, 24 V
The 270 kgf BTQ 300, twin counter-rotating propellers, 24 V. The manual gives a 500 A fuse at 24 V and a weight of 55.9 kg. Its cable is 3/0 for a total run under 5 m (positive plus negative), two 3/0 AWG per leg to 10 m, two 4/0 AWG per leg to 20 m. The manual's ladder tops out above it with a 48 V 300 kgf unit that no US page lists.
Where each point above comes from
- The boat comes out of the water to install it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it
Not sure this is the one? The thruster finder asks about your boat and prices every unit that fits.