Thrusterpedia

Which boat thruster, what it costs, how to get it installed

We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.

Drawing of a tunnel thruster: a tube through the bow below the waterline, the hull cut away to show the motor on top.
Our drawing of a tunnel thruster, the same for every maker. It is not VETUS’s own design.

VETUS · tunnel thruster · bow

VETUS Bow 95: specs, price and the boats it fits

It gives 210 to 231 lb of push, across two sizes. VETUS sells it for boats of 36 to 55 ft. It runs on 12 V or 24 V.

The unit$3,511Equipment only, Defender, read 26 October 2026
Installed by a yard, 45 ft boat$10,703 to $19,660Our estimate: the unit, labor, haul-out, battery and parts
  • Haul-out to install
  • DIY 2 of 5: wiring prep only
  • 3-year warranty

Choose a size

The VETUS Bow 95 comes in two sizes. Each has its own price, wiring and boats it suits. Pick one and the page below shows that size.

Every size side by side two sizes
Every size of the VETUS Bow 95
SizePushVoltageVETUS’s boat lengthPrice
Bow 95 at 12 V 210 lb (95 kgf) 12 V 36 to 55 ft $3,511
Bow 95 at 24 V 231 lb (105 kgf) 24 V 36 to 55 ft $3,511

From the database. The figures are VETUS’s and the dealers’.

Quick stats

  • Thrust 210 lb 95 kgf, VETUS's rating
  • Boat length 36 to 55 ft VETUS's own range
  • Price per lb of thrust $16.72 Unit only. $51 to $94 installed
  • Voltage 12 V As sold
  • Battery at 12 V 1,083 CCA One battery, near the thruster
  • Run limit 3 min Of continuous use at 12 V
  • To install it Haul-out The boat comes out of the water
  • Anodes $76.98 A change. More than twice another maker's

Quick stats

  • Thrust 231 lb 105 kgf, VETUS's rating
  • Boat length 36 to 55 ft VETUS's own range
  • Price per lb of thrust $15.20 Unit only. $46 to $84 installed
  • Voltage 24 V As sold
  • Battery at 24 V 533 CCA Two batteries, near the thruster
  • Run limit Not published Ask the maker before long use
  • To install it Haul-out The boat comes out of the water
  • Anodes $76.98 A change. More than twice another maker's

About the VETUS Bow 95

The Bow 95 is the big push-button VETUS for boats of about 36 to 55 ft, giving 210 to 231 lb of push. It has a long record on trawlers and sedan cruisers, and its plain on/off control is easy for anyone aboard to use.

US dealers sell it for $3,511, the same at 12 V or 24 V. Expect around $533 to $1,358 more for its tube, a panel at the helm, the main switch and a fuse. It needs its own battery bank close to the bow, and with cable and charging we estimate $739 to $1,101. See the full list.

Read more

One owner of a converted Navy utility trawler ran a 2006 Bow 95 for years, then had the motor rebuilt at a local alternator shop in about ten days for less than half the price of a new one. VETUS rates it for 3 minutes at a time on 12 V and 3.5 on 24 V. Check brushes and zinc every year. The warranty runs three years.

The full spec sheet for a yard sits lower down, and the VETUS thruster review covers VETUS’s whole range.

Where this summary comes from (6 sources, read 12 October 2026)

Will the VETUS Bow 95 steer your boat?

57 FT TRAWLER · BOW · 15 KT WIND

Size forThis page always opens on Steering.

Every knot figure here is wind speed, not boat speed or current.

Steers her at 15 kt

On a 57 ft trawler the VETUS Bow 95 (210 lb) steers her in a 15 knot breeze. Her bow needs about 218 lb from a tunnel to steer her in a 15 knot breeze. Its 210 lb lands within 15 percent of that figure, which this site counts as enough.

The finder leaves it off her list. It shows the Bow 95 at 24 V for her instead.

19.9 FT LEVER VETUS Bow 95 pivot

A tunnel at the bow of a 57 ft trawler 218 lb ★ this unit · 1 to 3: the three cheapest others that steer her at 13 kt or more, installed

  1. ★ VETUS Bow 95 this unit 210 lb · tunnel from $11,043 Steers her at 15 kt
  2. 1 Lewmar 185TT 6.0kW 214 lb · tunnel from $11,056 Steers her at 15 kt
  3. 2 Max Power CT125 (24 V) 254 lb · tunnel from $11,731 Steers her at 16 kt
  4. 3 VETUS Bow 95 Ignition Protected at 24 V 231 lb · tunnel from $11,845 Steers her at 15 kt

The VETUS Bow 95 on a trawler, by length

  1. 25 ft33 kt
  2. 30 ft28 kt
  3. 35 ft24 kt
  4. 40 ft21 kt
  5. 45 ft19 kt
  6. 50 ft17 kt
  7. 55 ft15 kt
  8. 60 ft14 kt
  9. 65 ft13 kt
  10. 70 ft12 kt
  11. 75 ft11 kt
  12. 80 ft11 kt

Outlined: the finder does not list it at that length (under 13 kt, far more than she needs, or outside VETUS’s own length range).

  • Under 10 kt
  • 10 to 15 kt
  • 15 to 20 kt: the sweet spot
  • Over 20 kt: more than she needs

Prices are the low end of the installed total, from our estimate. For your own boat, drive and installer, the finder prices each unit.

Is it right for your boat?

What VETUS says 36 to 55 ft The maker's own range, from its listing
What our sizing says 43 to 60 ft Full thrust in 15 knots, across the kinds of boat it fits
Every kind of boat it fits, by length ten boat types
Which boats it fits, by length
Boat Full thrust at 15 knotsStill a fit, in lighter wind
Pontoon & tritoon Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats.
Sailboat 40 to 58 ft 59 to 60 ftfull thrust to about 14 knots at 60 ft
Houseboat 33 to 43 ft 44 to 49 ftfull thrust to about 13 knots at 49 ft
Catamaran 46 to 60 ft None
Trawler 40 to 57 ft 58 to 60 ftfull thrust to about 14 knots at 60 ft
Motor yacht 40 to 57 ft 58 to 60 ftfull thrust to about 14 knots at 60 ft
Bass & flats Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one.
Wake & ski boats Not listed. Nobody sells a tunnel kit for these hulls.
Express cruiser 51 to 60 ft None
Center console No length. More thrust than the boat needs.

The VETUS Bow 95 against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.

The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit steers her in a 13 or 14 knot wind, within 15 percent of the 15 knot breeze this site sizes for. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.

How we size it

Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 43 ft, and a catamaran to 60 ft. The maker gives one range for every boat.

The table tries the VETUS Bow 95 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.

A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 33 ft and up to 60 ft, just past VETUS’s own range (36 to 55 ft).

It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the installing. The compare page sets this unit beside others.

What it costs installed

A yard job, everything in. Our estimate.

Installed by a yard
Boat Total installed
33 ft $10,523 to $13,320$50 to $63 a lb of thrust
45 ft $10,733 to $19,660$51 to $94 a lb of thrust
60 ft $11,093 to $21,470$53 to $102 a lb of thrust

From the shortest to the longest boat it is sized for.

What is in each total five lines

These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $590 to $2,900 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. The cost page builds the same figures line by line.

Each line of the estimate
Boat length The unit Yard labor Haul-out Batteries, cable, charger Other parts
33 ft $3,511 $5,120 to $5,760about 32 hours $590 to $1,590 $769 to $1,101 $533 to $1,358
45 ft $3,511 $5,120 to $11,52032 to 64 hours $800 to $2,170 $769 to $1,101 $533 to $1,358
60 ft $3,511 $5,120 to $12,60032 to 70 hours $1,160 to $2,900 $769 to $1,101 $533 to $1,358

For every length in the table above.

How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.

Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 26 October 2026.

  • At 12 V: one 12 V battery, at least 1,083 CCA (VETUS’s minimum), $443 to $552 for the battery; VETUS’s cable table gives 3/0 to 2 x 2/0 AWG, priced on 4/0 to 2 x 2/0 AWG, the nearest size cut to length: $180 to $403 for the red and black cable and the lugs; a GEN5X2 charger, $146.

The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.

DIY breakdown

DIY 2 of 5: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.

DIY levels

  • Level 5: Owner install. No yard, no electrician.
  • Level 4: You install it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
  • Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
  • Level 2: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.
  • Level 1: Yard job. A qualified professional does all of it.

You Yard Electrician. The bar is labor hours; a haul-out is a note.

How we rate DIY

You: 4 to 16 hours Yard: 32 to 70 hours Electrician: 2 to 4 hours Plus a haul-out.

Your part needs:Heavy battery cableCrimping big lugs

Every step, and who does it three steps
  1. Cut, bond and fair the tunnel; fit the gear leg, motor and propeller Yard 32 to 70 hours The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
  2. Mount the battery box, switch and fuse holder; run and secure the cables You 4 to 16 hours Our estimate. No maker times this step, and a first-time owner is slower than a yard, so the range is wide.
  3. Final connections at the battery and the motor, load test Electrician 2 to 4 hours Our estimate. Nobody publishes a time for the final connections and test on their own.

A qualified marine electrician should make the final connections and test them before first use. Hours are labor only.

Will the VETUS Bow 95 steer your boat?

60 FT TRAWLER · BOW · 15 KT WIND

Size forThis page always opens on Steering.

Every knot figure here is wind speed, not boat speed or current.

Steers her at 15 kt

On a 60 ft trawler the VETUS Bow 95 (231 lb) steers her in a 15 knot breeze. Her bow needs about 240 lb from a tunnel to steer her in a 15 knot breeze. Its 231 lb lands within 15 percent of that figure, which this site counts as enough.

The finder lists it for her.

21 FT LEVER VETUS Bow 95 pivot

A tunnel at the bow of a 60 ft trawler 240 lb ★ this unit · 1 to 3: the three cheapest others that steer her at 13 kt or more, installed

  1. ★ VETUS Bow 95 this unit 231 lb · tunnel from $11,063 Steers her at 15 kt
  2. 1 Lewmar 185TT 6.0kW 214 lb · tunnel from $11,106 Steers her at 14 kt
  3. 2 Max Power CT125 (24 V) 254 lb · tunnel from $11,781 Steers her at 15 kt
  4. 3 VETUS Bow 95 Ignition Protected at 24 V 231 lb · tunnel from $11,895 Steers her at 15 kt

The VETUS Bow 95 on a trawler, by length

  1. 25 ft35 kt
  2. 30 ft29 kt
  3. 35 ft25 kt
  4. 40 ft22 kt
  5. 45 ft20 kt
  6. 50 ft18 kt
  7. 55 ft16 kt
  8. 60 ft15 kt
  9. 65 ft14 kt
  10. 70 ft12.5 kt
  11. 75 ft12 kt
  12. 80 ft11 kt

Outlined: the finder does not list it at that length (under 13 kt, far more than she needs, or outside VETUS’s own length range).

  • Under 10 kt
  • 10 to 15 kt
  • 15 to 20 kt: the sweet spot
  • Over 20 kt: more than she needs

Prices are the low end of the installed total, from our estimate. For your own boat, drive and installer, the finder prices each unit.

Is it right for your boat?

What VETUS says 36 to 55 ft The maker's own range, from its listing
What our sizing says 45 to 60 ft Full thrust in 15 knots, across the kinds of boat it fits
Every kind of boat it fits, by length ten boat types
Which boats it fits, by length
Boat Full thrust at 15 knotsStill a fit, in lighter wind
Pontoon & tritoon Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats.
Sailboat 42 to 60 ft None
Houseboat 33 to 45 ft 46 to 51 ftfull thrust to about 13 knots at 51 ft
Catamaran 48 to 60 ft None
Trawler 42 to 60 ft None
Motor yacht 42 to 60 ft None
Bass & flats Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one.
Wake & ski boats Not listed. Nobody sells a tunnel kit for these hulls.
Express cruiser 53 to 60 ft None
Center console No length. More thrust than the boat needs.

The VETUS Bow 95 against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.

The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit steers her in a 13 or 14 knot wind, within 15 percent of the 15 knot breeze this site sizes for. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.

How we size it

Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 45 ft, and a sailboat to 60 ft. The maker gives one range for every boat.

The table tries the VETUS Bow 95 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.

A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 33 ft and up to 60 ft, just past VETUS’s own range (36 to 55 ft).

It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the installing. The compare page sets this unit beside others.

What it costs installed

A yard job, everything in. Our estimate.

Installed by a yard
Boat Total installed
33 ft $10,493 to $13,019$45 to $56 a lb of thrust
45 ft $10,703 to $19,359$46 to $84 a lb of thrust
60 ft $11,063 to $21,169$48 to $92 a lb of thrust

From the shortest to the longest boat it is sized for.

What is in each total five lines

These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $590 to $2,900 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. The cost page builds the same figures line by line.

Each line of the estimate
Boat length The unit Yard labor Haul-out Batteries, cable, charger Other parts
33 ft $3,511 $5,120 to $5,760about 32 hours $590 to $1,590 $739 to $800 $533 to $1,358
45 ft $3,511 $5,120 to $11,52032 to 64 hours $800 to $2,170 $739 to $800 $533 to $1,358
60 ft $3,511 $5,120 to $12,60032 to 70 hours $1,160 to $2,900 $739 to $800 $533 to $1,358

For every length in the table above.

How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.

Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 26 October 2026.

  • At 24 V: two 12 V batteries in series, at least 533 CCA each (VETUS’s minimum), $513 for both; VETUS’s cable table gives 2 to 1 AWG, priced on 1 AWG, the nearest size cut to length: $80 to $141 for the red and black cable and the lugs; a GEN5X2 charger, $146.

The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.

DIY breakdown

DIY 2 of 5: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.

DIY levels

  • Level 5: Owner install. No yard, no electrician.
  • Level 4: You install it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
  • Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
  • Level 2: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.
  • Level 1: Yard job. A qualified professional does all of it.

You Yard Electrician. The bar is labor hours; a haul-out is a note.

How we rate DIY

You: 4 to 16 hours Yard: 32 to 70 hours Electrician: 2 to 4 hours Plus a haul-out.

Your part needs:Heavy battery cableCrimping big lugs

Every step, and who does it three steps
  1. Cut, bond and fair the tunnel; fit the gear leg, motor and propeller Yard 32 to 70 hours The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
  2. Mount the battery box, switch and fuse holder; run and secure the cables You 4 to 16 hours Our estimate. No maker times this step, and a first-time owner is slower than a yard, so the range is wide.
  3. Final connections at the battery and the motor, load test Electrician 2 to 4 hours Our estimate. Nobody publishes a time for the final connections and test on their own.

A qualified marine electrician should make the final connections and test them before first use. Hours are labor only.

Related videos

One from VETUS’s own channel and three from other channels. Each one is labeled. They play from YouTube only when you tap. Take any claim in a video back to the figures on this page, which are the ones we checked.

Installing a Vetus Bow ThrusterMagazine Power and Motoryacht, September 2020
Massive Upgrade- VETUS BOW THRUSTER; ENGINE & DC PANEL update [E22]Owner install Sailing Squalo, September 2022
Vetus bow thruster anode replacement on an Albin 28' yacht by Daily Divers Boat Service.Service how-to Daily Divers Boat Services, May 2025
Bow Thruster maintenance part 1Maker VETUS’s own channel

Know before you buy

What sets this model apart, what it costs to keep, and what to weigh.

Price per pound of thrust

$16.72 a lb The unit’s price over its published thrust, on the smallest size. The bars are VETUS’s next sizes and the nearest other makers.

Controls

The solenoid switches and the 5 A control fuse are on the motor. The panel, its cable, the main fuse and switch are bought.

Pricey wear part: anodes

$76.98 a change

A change costs $76.98. That is over three times the $20.89 for Lewmar’s anode on the same 185 mm tunnel (589350, Fisheries Supply). An anode is a plain block of metal that wears away by design, so you will buy it again.

They sit below the waterline, so a change means a haul-out or a diver.

Service and warranty

VETUS gives 3 years, or 1 for professional use, and it transfers to the next owner. Claims go through the dealer only. It is void unless an authorized VETUS dealer does the periodic maintenance, and transport, labor and lifting are excluded.

See VETUS’s warranty VETUS's warranty policy.

Special mentions

Battery: at 12 V it wants one battery of 1,083 CCA or more, VETUS's figure. The cheapest that meets it is the Dyno Group 8D heavy duty marine starting (flooded), $443.02. A sealed one is the Lifeline GPL-3100HC Group 31 AGM starting, $551.95. Check your own bank.

Charger: a NOCO GEN5X2 two-bank shore charger, $146.41. It is the one our estimate prices.

Gas engine room? Buy the ignition-protected VETUS Bow 95 Ignition Protected, $4,343.

Dealer prices at Fisheries Supply, read 26 October 2026.

What to weigh

The boat comes out of the water to install it: it needs a tunnel bore below the waterline.

Short pushes only: VETUS rates the motor for 3 min at a stretch.

At 12 V it draws 650 A, so the battery cable is heavy and the battery sits close to it.

Parts for the VETUS Bow 95

See the VETUS Bow 95 manual

Search for the number as printed here, with no spaces. Prices are each dealer’s on the day shown, before shipping and tax. Check the plate on your motor before you order: some parts change with the tunnel size, the voltage or the year.

For the install what the box leaves you to buy

15 parts

The manual button above opens it on the maker's site. It has the hull, wiring and fuse figures for this model.

From VETUS’s BOW95D installation manual 020526.08 r7, January 2025, read 25 October 2026.

In the box
The manual prints no box list. It says the thruster is supplied with a zinc anode and has you drill with the template that comes with it.
Bought separately
The tunnel, the main switch (BATSW250 or BATSW600), the main fuse (ZE) and holder (ZEHC100), the cable, the control panel and its cable.
Charging
The manual wants the thruster on its own battery or batteries, close by so the power cables stay short, and sealed batteries if they share its compartment. Its wiring diagram shows an alternator and a battery separator, and it says nothing more about charging.

The manual’s words, page 22: “We also recommend that each bow thruster is powered by its own separate battery or batteries.”

The “other parts” line in the estimate above covers these parts as a range, $533 to $1,358 at Fisheries Supply’s prices on 30 September 2026 and 26 October 2026, because the exact items depend on your boat. The batteries, cable and charger have a line of their own. The cost page has what every maker says about each part.

Tunnel tube

Fisheries Supply lists it as “VETUS fiberglass tunnel tube, 185 mm bore, 40 in”.

Sold in lengths from about 40 to 60 in. This is the shortest: the yard cuts the tube to the width of your hull at the thruster.

Part number BP185G10

Control panel

Fisheries Supply lists it as “VETUS push-button thruster panel with time delay”.

Part number BPSE2

Control cable, panel to thruster

Fisheries Supply lists it as “VETUS bow thruster control cable, 6 m”.

Sold in lengths from 6 to 20 m. This is the shortest: measure the run from the helm to the thruster and buy the length that reaches.

Part number BP29

Main fuse

Ask for 425 A (VETUS ZE425). This one is for the 12 V version.

A VETUS strip fuse in its own holder (VETUS ZEHC100). Not listed at Fisheries Supply; ask a VETUS dealer.

Part number See the line above.

Main fuse

Ask for 200 A (VETUS ZE200). This one is for the 24 V version.

A VETUS strip fuse in its own holder (VETUS ZEHC100). Not listed at Fisheries Supply; ask a VETUS dealer.

Part number See the line above.

Fuse holder

Ask for VETUS ZEHC100 strip fuse holder.

Ask a VETUS dealer.

Part number See the line above.

Battery switch

Fisheries Supply lists it as “HD-Series 600 A battery switch, on/off”. This one is for the 12 V version.

Rated at or above the 425 A main fuse. If your manual names its own switch, use that one.

Part number 3000

Battery switch

Fisheries Supply lists it as “m-Series 300 A battery switch, on/off”. This one is for the 24 V version.

Rated at or above the 200 A main fuse. If your manual names its own switch, use that one.

Part number 2306

Batteries

Fisheries Supply lists it as “Dyno Group 8D heavy duty marine starting (flooded)”. This one is for the 12 V version.

One at 1,083 CCA or more. The cheapest listing that meets it.

Part number DNO 8DC

Batteries

Fisheries Supply lists it as “Lifeline GPL-1400T AGM starting”. This one is for the 24 V version.

You need 2, each at 533 CCA or more, in series for 24 V. The cheapest listing that meets it.

Part number LFL GPL-1400T

Battery cable, red and black

Defender lists it as “Ancor tinned battery cable 4/0 AWG, cut to length, red or black”. This one is for the 12 V version.

This is the short run. A longer run takes heavier cable: the wiring calculator sizes yours. You need 5 ft of each color. For about 10 ft of cable in all, out and back. Measure your run and check it against the cable table in the manual: never go smaller than it asks for.

Part number None on the listing. Order it by name.

Battery cable, red and black

Defender lists it as “Ancor tinned battery cable 1 AWG, cut to length, red or black”. This one is for the 24 V version.

You need 10 ft of each color. For about 20 ft of cable in all, out and back. Measure your run and check it against the cable table in the manual: never go smaller than it asks for.

Part number None on the listing. Order it by name.

Cable lugs

Fisheries Supply lists it as “Tin-plated starter lugs, 4/0 AWG, bag of 10”. This one is for the 12 V version.

This is the short run. A longer run takes heavier cable: the wiring calculator sizes yours. The listing runs $47.52 to $49.44 by stud size. Eight ends on one run, with two spare.

Part number 91066-P10

Cable lugs

Fisheries Supply lists it as “Tin-plated starter lugs, 1 AWG, bag of 10”. This one is for the 24 V version.

The listing runs $20.52 to $22.06 by stud size. Eight ends on one run, with two spare.

Part number 91066-P10

Charger

Fisheries Supply lists it as “GEN5X2 on-board charger, 10 A, 2 banks”.

Or a DC-to-DC charger from the house system: ask the electrician.

Part number GEN5X2

Outside the hull replacement parts in the water

6 parts

Zinc anode

The metal that wears away in the water so the drive does not. VETUS calls it “Zincanode c/w screws”.

From VETUS manual 020526.08.

Part number SET0150

Propeller

The propeller on the drive. VETUS calls it “Propeller c/w drive pin and mounting set”.

From VETUS manual 020526.08.

Part number SET0088

Drive pins, pack of 5

The pin that locks the propeller to its shaft. VETUS calls it “Propeller pins, 5 pcs”.

From VETUS manual 020526.08.

Part number BP275S

Gear leg gasket, 1 mm

The leg under the motor that turns the propeller. VETUS calls it “Gasket 1 mm”.

From VETUS manual 020526.08.

Part number BP1021

Gear leg gasket, 2 mm

The leg under the motor that turns the propeller. VETUS calls it “Gasket 2 mm”.

From VETUS manual 020526.08. The manual lists two of these.

Part number BP1020

Tailpiece (gear leg), complete

The leg under the motor that turns the propeller. VETUS calls it “Tailpiece compl.”.

From VETUS manual 020526.08.

Part number SET0046

Inside the boat replacement parts on board

15 parts

Flexible coupling

VETUS calls it “Coupling”.

From VETUS manual 020526.08.

Part number BP1202

Intermediate flange

VETUS calls it “Intermediate flange”.

From VETUS manual 020526.08.

Part number BP1199B

Motor brush kit

Carbon brushes inside the motor. They wear down with use. VETUS calls it “Set of 8 pcs of carbon brushes for BOW9512D”. It fits the 12V size on this page.

From VETUS manual 020526.08.

Part number SET0128

Motor brush kit

Carbon brushes inside the motor. They wear down with use. VETUS calls it “Set of 8 pcs of carbon brushes for BOW9524D”. It fits the 24V size on this page.

From VETUS manual 020526.08.

Part number SET0129

Replacement motor (comes with solenoids)

The heavy switch that sends battery power to the motor. VETUS calls it “Electromotor 5.7 kW - 12 V for BOW9512D c/w solenoid switches”. It fits the 12V size on this page.

From VETUS manual 020526.08. VETUS's webshop also lists motor set SET0159 under the name BOW9512/BOW12512. Confirm with VETUS.

Part number SET0041

Replacement motor (comes with solenoids)

The heavy switch that sends battery power to the motor. VETUS calls it “Electromotor 5.7 kW - 24 V for BOW9524D c/w solenoid switches”. It fits the 24V size on this page.

From VETUS manual 020526.08.

Part number SET0110

Solenoid set (the motor switch)

The heavy switch that sends battery power to the motor. VETUS calls it “Set of solenoid switches 12 V for BOW9512D”. It fits the 12V size on this page.

From VETUS manual 020526.08.

Part number SET0111

Solenoid set (the motor switch)

The heavy switch that sends battery power to the motor. VETUS calls it “Set of solenoid switches 24 V for BOW9524D”. It fits the 24V size on this page.

From VETUS manual 020526.08.

Part number SET0044

Control circuit fuse, 5 A

The main fuse at the battery, in the rating the maker gives. VETUS calls it “Spare fuse 5 A”.

From VETUS manual 020526.08.

Part number BP256

Main fuse

The main fuse at the battery, in the rating the maker gives. VETUS calls it “Fuse slow blow, Vetus art. code ZE425”. It fits the 12V size on this page.

From VETUS manual 020526.08. The 12 V model's rating in the manual's battery and cable table; VETUS's 2022 parts guide agrees. Fuse holder ZEHC100.

Part number ZE425

Main fuse

The main fuse at the battery, in the rating the maker gives. VETUS calls it “Fuse slow blow, Vetus art. code ZE200”. It fits the 24V size on this page.

From VETUS manual 020526.08. The 24 V model's rating in the manual's battery and cable table; VETUS's 2022 parts guide agrees. Fuse holder ZEHC100.

Part number ZE200

Thermal protection switch

It cuts the motor out when it runs too hot. VETUS calls it “Thermal Protection for BOW9512D”. It fits the 12V size on this page.

From VETUS manual 020526.08.

Part number TS110

Thermal protection switch

It cuts the motor out when it runs too hot. VETUS calls it “Thermal Protection for BOW9524D”. It fits the 24V size on this page.

From VETUS manual 020526.08.

Part number TS95

Control panel, on/off dual joystick (bow and stern)

The control at the helm. VETUS calls it “Dual joystick panel with time delay”.

Runs a bow and a stern thruster.

Part number BPJDE2

Control panel, on/off joystick

The control at the helm. VETUS calls it “Joystick panel with time delay”.

For one thruster.

Part number BPJE2
See it at Defender$347.81 Price read 29 Oct 2026

The install parts are matched to VETUS’s own figures and priced at Fisheries Supply, with the battery cable at Defender, cut to length.

Spare part numbers come from VETUS’s parts pages and manuals. A dealer may sell a part we have not priced. Search for the number.

Other sizes and close alternatives

Compare them side by side

The other makers listed are the nearest match each makes, of the same style and for the same end, within a quarter of its thrust. The compare page lists every model, and the thruster index lists every model with a page here.

For the yard and the installer

Every published figure, with its source.

Full spec sheet thrust, motor, mounting, price, part number, documents
Full spec sheet
Thrust and motor
Thrust 210 lb (95 kgf) As printed: Thrust (in lbs force): 210
Motor5.7 kW
Voltage12 V
Run limit3 min of continuous use at 12 V
Installation
TypeTunnel, fixed mount
End of the boatBow
Tunnel diameter185 mm
What it does to the hullTunnel bore below the waterline
Haul-out to install itYes
Maker’s boat length36 to 55 ft
Price and ordering
Price $3,511 equipment only, a dealer's price, defender.com, 26 October 2026
Part number BOW9512D12 V
BOW9524D24 V
Documents
Manual Installation manual (PDF)on the maker's site
The site’s reviewVETUS thruster review

Every published figure the site holds for the VETUS Bow 95, with where each came from.

Draw, cable, fuse and battery at each voltage 12 V

These are the maker’s own figures, at each voltage it is sold at. The cable is the size for the shortest run in the maker’s table. A longer run may need heavier cable, and the wiring calculator works that out for your own boat.

Draw, cable, fuse and battery
Voltage Draw Maker’s cable Fuse Battery Run limit
12 V 650 Anominal draw 1/0 AWG for up to 8 ft of cable counted out and back. Longer runs take heavier cableinstallation manual 020526.08, r07, January 2025 425 Ainstallation manual 020526.08, r07, January 2025 1,083 CCA minimum, 2,166 CCA maximumVETUS installation manual 020526.08, r07, January 2025 3 min of continuous use at 12 Vinstallation manual 020526.08, r07, January 2025

The VETUS Bow 95’s draw, cable, fuse, battery and run limit, as the maker publishes them.

Our notes from the manual and listings

In the box: The solenoid switches and the 5 A control fuse are on the motor. The panel, its cable, the main fuse and switch are bought.

12 V

A 185 mm tunnel. The manual gives 650 A, a battery of 1083 to 2166 cold cranking amps and a 425 A fuse. For cable it gives 1 AWG to 8.5 ft of total run (positive plus negative), and 4/0 to 20.7 ft. The motor is brushed. The manual rates it for 3 minutes at a time, or 3 per hour, at 650 A.

Brushes and anode are checked yearly, and no copper-based antifouling goes on the unit. The product page prints 610 A where the manual says 650. From 95 kgf up the manual's minimum brush length is 16 mm, not 14. Defender sells the 12 V and 24 V versions as one listing at one price. The warranty runs three years and is claimed through the dealer only. It is void unless an authorized VETUS dealer does the periodic maintenance, and labor, transport and lifting are excluded.

24 V

The 24 V BOW95 on two 12 V batteries in series. The manual gives 320 A, a battery of 533 to 1067 cold cranking amps and a 200 A fuse. For cable it gives 4 AWG to 17.7 ft of total run (positive plus negative), and 4/0 to 85.3 ft. The manual rates it for 3.5 minutes at a time, or 3.5 per hour, at 320 A.

Where each point above comes from
  • The boat comes out of the water to install it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it

For the yard and the installer

Every published figure, with its source.

Full spec sheet thrust, motor, mounting, price, part number, documents
Full spec sheet
Thrust and motor
Thrust 231 lb (105 kgf) As printed: Thrust (in lbs force): 231
Motor5.7 kW
Voltage24 V
Run limitNot published
Installation
TypeTunnel, fixed mount
End of the boatBow
Tunnel diameter185 mm
What it does to the hullTunnel bore below the waterline
Haul-out to install itYes
Maker’s boat length36 to 55 ft
Price and ordering
Price $3,511 equipment only, a dealer's price, defender.com, 26 October 2026
Part number BOW9512D12 V
BOW9524D24 V
Documents
Manual Installation manual (PDF)on the maker's site
The site’s reviewVETUS thruster review

Every published figure the site holds for the VETUS Bow 95, with where each came from.

Our notes from the manual and listings

In the box: The solenoid switches and the 5 A control fuse are on the motor. The panel, its cable, the main fuse and switch are bought.

12 V

A 185 mm tunnel. The manual gives 650 A, a battery of 1083 to 2166 cold cranking amps and a 425 A fuse. For cable it gives 1 AWG to 8.5 ft of total run (positive plus negative), and 4/0 to 20.7 ft. The motor is brushed. The manual rates it for 3 minutes at a time, or 3 per hour, at 650 A.

Brushes and anode are checked yearly, and no copper-based antifouling goes on the unit. The product page prints 610 A where the manual says 650. From 95 kgf up the manual's minimum brush length is 16 mm, not 14. Defender sells the 12 V and 24 V versions as one listing at one price. The warranty runs three years and is claimed through the dealer only. It is void unless an authorized VETUS dealer does the periodic maintenance, and labor, transport and lifting are excluded.

24 V

The 24 V BOW95 on two 12 V batteries in series. The manual gives 320 A, a battery of 533 to 1067 cold cranking amps and a 200 A fuse. For cable it gives 4 AWG to 17.7 ft of total run (positive plus negative), and 4/0 to 85.3 ft. The manual rates it for 3.5 minutes at a time, or 3.5 per hour, at 320 A.

Where each point above comes from
  • The boat comes out of the water to install it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it

Not sure this is the one? The thruster finder asks about your boat and prices every unit that fits.

Where to go next

The specs are the maker’s and the dealers’, on the dates shown. The sizing and the costs are our arithmetic, done without seeing your boat.