We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.
Sleipner · retractable thruster · bow or stern
Sleipner SRP100 PRO: specs, price and the boats it fits
It gives 256 lb (116 kgf) of push. Sleipner sells it for boats of 33 to 56 ft. It runs on 12 V or 24 V.
- Haul-out to install
- DIY 2 of 5: wiring prep only
- 2-year warranty
Not sold in the US right now. No US store or distributor lists the Sleipner SRP100 PRO: we checked Imtra’s US catalog (the Sleipner distributor), Defender and Fisheries Supply on 15 October 2026. Its specs and parts stay here for owners of boats built or bought abroad. For one to buy here, see the models on the Sleipner (Side-Power) review that have a US price.
Quick stats
- Thrust 256 lb 116 kgf, Sleipner's rating
- Boat length 33 to 56 ft Sleipner's own range
- Price per lb of thrust Not worked out It needs a price and a thrust figure
- Voltage 12 V or 24 V As sold
- Battery Not published Ask the maker before wiring
- Run limit Not published Ask the maker before long use
- To install it Haul-out The boat comes out of the water
- Anodes $42.30 A change, at Defender
About the Sleipner SRP100 PRO
The SRP100 adds speed control to the SR100: up to 256 lb of push for boats of about 33 to 56 ft, at 12 or 24 V, from the same 185 mm retractable.
Neither Sleipner nor Imtra prints a price, so ask a dealer. No installation manual is posted for it; the product page gives 740 A and an ANL 500 fuse at 12 V, 340 A and an ANL 325 at 24 V. See the specs.
Read more
Full thrust lasts 2 to 3 minutes; lower settings stretch that. At 12 V the current calls for two strong batteries near the unit. Warranty: two years.
Installing it yourself? The installer section has every spec, and the Sleipner (Side-Power) review sets this model against the rest of the Sleipner range.
Sleipner sold its thrusters under the Side-Power name until 2021, and many dealers and owners still call them that. It is the same company and the same thrusters.
Where this summary comes from (3 sources, read 15 October 2026)
Will the Sleipner SRP100 PRO steer your boat?
61 FT TRAWLER · BOW · 15 KT WIND
Every knot figure here is wind speed, not boat speed or current.
On a 61 ft trawler the Sleipner SRP100 PRO (256 lb) steers her in a 15 knot breeze. Her bow needs about 248 lb from a retractable to steer her in a 15 knot breeze.
The finder leaves it off her list. We found no US store that sells it, and the finder lists only units you can buy here.
The Sleipner SRP100 PRO on a trawler, by length
- 25 ft37 kt
- 30 ft31 kt
- 35 ft26 kt
- 40 ft23 kt
- 45 ft21 kt
- 50 ft19 kt
- 55 ft17 kt
- 60 ft15 kt
- 65 ft14 kt
- 70 ft13 kt
- 75 ft12 kt
- 80 ft12 kt
Outlined: the finder does not list it at that length (under 13 kt, far more than she needs, or outside Sleipner’s own length range).
- Under 10 kt
- 10 to 15 kt
- 15 to 20 kt: the sweet spot
- Over 20 kt: more than she needs
Prices are the low end of the installed total, from our estimate. For your own boat, drive and installer, the finder prices each unit.
Is it right for your boat?
Every kind of boat it fits, by length
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A retractable drops down inside the hull, and a pontoon has no hull depth to drop into. | |
| Sailboat | 45 to 61 ft | None |
| Houseboat | 34 to 48 ft | 49 to 54 ftfull thrust to about 13 knots at 54 ft |
| Catamaran | 51 to 61 ft | None |
| Trawler | 45 to 61 ft | None |
| Motor yacht | 45 to 61 ft | None |
| Bass & flats | Not listed. A retractable needs hull depth to drop into, and these planing hulls have almost none forward. | |
| Wake & ski boats | Not listed. A retractable needs hull depth to drop into, and these planing hulls have almost none forward. | |
| Express cruiser | 57 to 61 ft | None |
| Center console | No length. More thrust than the boat needs. | |
The Sleipner SRP100 PRO against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.
The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit steers her in a 13 or 14 knot wind, within 15 percent of the 15 knot breeze this site sizes for. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
How we size it
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 48 ft, and a sailboat to 61 ft. The maker gives one range for every boat.
The table tries the Sleipner SRP100 PRO on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs up to 61 ft, just past Sleipner’s own range (33 to 56 ft).
It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the installing. The compare page sets this unit beside others.
What it costs installed
No US dollar price is published for the Sleipner SRP100 PRO, so we build no total for it. The yard’s share of the job is on the cost page.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
DIY breakdown
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You install it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard installs the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: 4 to 16 hours Yard: 40 to 88 hours Electrician: 2 to 4 hours Plus a haul-out.
Your part needs:Heavy battery cableCrimping big lugs
Every step, and who does it
- Cut the hull and fit the housing and mechanism Yard 40 to 88 hours Nobody publishes an hours figure. Fisheries Supply says installation is significantly more expensive than a tunnel, and that is too loose to turn into a number. So this is the tunnel’s own banded figure plus a quarter, which keeps it above a tunnel as the distributors describe it.
- Mount the battery box, switch and fuse holder; run and secure the cables You 4 to 16 hours Our estimate. No maker times this step, and a first-time owner is slower than a yard, so the range is wide.
- Final connections at the battery and the motor, load test Electrician 2 to 4 hours Our estimate. Nobody publishes a time for the final connections and test on their own.
A qualified marine electrician should make the final connections and test them before first use. Hours are labor only.
Related videos
Two from Sleipner’s own channel and one from other channels. Each one is labeled. They play from YouTube only when you tap. Take any claim in a video back to the figures on this page, which are the ones we checked.
Know before you buy
What sets this model apart, what it costs to keep, and what to weigh.
Price per pound of thrust
There is no US price to divide by its thrust.
Controls
Proportional: the joystick sets how hard it pushes. The power controller (PPC) is included.
Anodes
$42.30 a change- Anode (SM71190A): $14.40 at Defender, $18.01 at Fisheries Supply, and it takes two.
- Anode on the retract mechanism (zinc) (SM61180): $13.50 at Defender, $16.88 at Fisheries Supply.
They sit below the waterline, so a change means a haul-out or a diver.
Service and warranty
Sleipner gives 2 years for leisure use and 1 for commercial use. It transfers to the next owner, and it starts no later than 18 months after the boat's first launch.
See Sleipner’s warranty Sleipner's warranty statement, effective 1 April 2022.Special mentions
Sleipner sells it for either end, so it can go at the bow or the stern.
Dealer prices at Fisheries Supply, read 26 October 2026.What to weigh
The boat comes out of the water to install it: it needs a large hull opening below the waterline.
No US dollar price is published for it, so we can work out no installed cost.
Parts for the Sleipner SRP100 PRO
See the Sleipner SRP100 PRO manualThe US dealer number comes first, then Sleipner’s own. Prices are each dealer’s on the day shown, before shipping and tax. Check the plate on your motor before you order: some parts change with the tunnel size, the voltage or the year.
For the install what the box leaves you to buy
The manual button above opens it on the maker's product page. It has the hull, wiring and fuse figures for this model.
From Sleipner’s SR80 and SR100 installation manual, document 2755 rev 9, 2025, read 16 October 2026.
- In the box
- The manual prints no box list.
- Bought separately
- The battery, the ANL fuse, a main switch (manual or Sleipner's automatic one), the battery cable, the control panel, and the S-Link cables with their T-connectors and end terminators.
- Charging
- The word "charging" is not in any of the Sleipner guides we read. The battery is sized by cold cranking amps, and a battery near the thruster is suggested. How it gets charged is left to you and your installer.
In Sleipner’s words, from its SE80 to SE150 installation guide, document 2687 rev 30, page 19: “For installations on large vessels with bow and stern thrusters or catamarans a dedicated battery for each thruster should be considered.”
A yard job adds these parts on top of the unit: $336 to $815 for the priced ones, at Fisheries Supply’s prices on 30 September 2026 and 26 October 2026, plus the batteries, cable and charger. The cost page has what every maker says about each part.
Outside the hull replacement parts in the water
Anode (takes two)
The metal that wears away in the water so the drive does not. Sleipner calls it “Anode, aluminium SE60/80/100”.
Anode on the retract mechanism (zinc)
The metal that wears away in the water so the drive does not. Sleipner calls it “Anode, zinc 4/6 Hp up to 1999”.
Sleipner's name for it says "4/6 Hp up to 1999", but its parts lists show it in the retract mechanism of these models (SM900460 6 1180 on the SRV/SRL pages).
Propeller (185 mm)
The propeller on the drive. Sleipner calls it “Propeller SE80/100 5bl Q-Prop™”.
Drive pin (the pin that drives the propeller)
The pin that locks the propeller to its shaft. Sleipner calls it “Drive pin propeller SE60/80/100 (4/6/7HP)”.
Gear leg gasket
The leg under the motor that turns the propeller. Sleipner calls it “Gasket for gearleg/tunnel SE80/100 1,5mm”.
Inside the boat replacement parts on board
End stop sensor kit, 12 V
Sleipner calls it “End stop sensor kit 12V”. It fits the 12V size on this page.
End stop sensor kit, 24 V
Sleipner calls it “End stop sensor kit 24V”. It fits the 24V size on this page.
Lift actuator, 12 V
Sleipner calls it “Actuator retract, complete 12V”. It fits the 12V size on this page.
Listed for the SRP80/100 12 V and the SR80/100 12 V retract assembly 8 0650-12.
Lift actuator, 24 V
Sleipner calls it “Actuator retract, complete 24V”. It fits the 24V size on this page.
Listed for the SRP80/100 24 V and the SR80/100 24 V retract assembly 8 0650-24.
Solenoid (the motor switch)
The heavy switch that sends battery power to the motor. Sleipner calls it “Solenoid SE80/100/120/130/150/170 24V”. It fits the 24V size on this page.
Solenoid kit
The heavy switch that sends battery power to the motor. Sleipner calls it “Solenoid kit SR80 12V”. It fits the 12V size on this page.
Solenoid kit
The heavy switch that sends battery power to the motor. Sleipner calls it “Solenoid kit SR80 24V”. It fits the 24V size on this page.
Retract control box
The electronics that run the motor when you press the panel. Sleipner calls it “Control box retract”.
Listed for the SRP80/100 and for the SR100 motors 8 0105 12 and 8 0105 24.
Main fuse (325 A)
The main fuse at the battery, in the rating the maker gives. Sleipner calls it “Recommended fuse A”. It fits the 24V size on this page.
The rating Sleipner prints on the own page of each model listed here; read on each page.
Main fuse (500 A)
The main fuse at the battery, in the rating the maker gives. Sleipner calls it “Recommended fuse A”. It fits the 12V size on this page.
The rating Sleipner prints on the own page of each model listed here; read on each page.
Replacement motor
The electric motor that turns the propeller. Sleipner calls it “Electric motor SRP100 12V”. It fits the 12V size on this page.
Replacement motor
The electric motor that turns the propeller. Sleipner calls it “Electric motor SRP100 24V”. It fits the 24V size on this page.
No part matches. Try the number without spaces, or the part’s name.
Spare part numbers come from Sleipner’s parts pages and manuals. A dealer may sell a part we have not priced. Search for the number.
Other sizes and close alternatives
- Size down Sleipner SRP80 PRO 212 lb · $14,700
- Size up Sleipner ERL130 eVision 287 lb
- Same thrust Sleipner SRV100 256 lb · $11,750
- Same thrust Sleipner SRVP100 PRO 256 lb · $13,070
- Same thrust Sleipner SR100 256 lb
- Same thrust Sleipner SRL100 256 lb
- Same thrust Sleipner SRLP100 PRO 256 lb
- Other maker Max Power VIP 150 three sizes, 212 to 254 lb · $8,598 to $8,698
- Other maker Quick BTR 185 six sizes, 143 to 231 lb · $12,436 to $17,991
- Other maker Lewmar RT185 MX Gen 2 214 lb · $8,687 to $9,034
The other makers listed are the nearest match each makes, of the same style and for the same end, within a quarter of its thrust. The compare page lists every model, and the thruster index lists every model with a page here.
For the yard and the installer
Every published figure, with its source.
Full spec sheet
| Thrust and motor | |
|---|---|
| Thrust | 256 lb (116 kgf) As printed: at 12V: 116kg; at 10.5V (nominal): 100kg |
| Thrust under load | 220 lb at 10.5 V |
| Motor | 6.3 kW |
| Voltage | 12 V or 24 V |
| Run limit | Not published |
| Installation | |
| Type | Retractable, drops down |
| End of the boat | Bow or stern |
| Tunnel diameter | 185 mm |
| What it does to the hull | Large hull opening below the waterline |
| Haul-out to install it | Yes |
| Maker’s boat length | 33 to 56 ft |
| Price and ordering | |
| Price | No US price published |
| Part number | SRP100/185T-12V12 V, 12 V DC (nominal 10.5 V DC) SRP100/185T-24V24 V, 24 V DC (nominal 21 V DC) |
| Documents | |
| Manual | Installation manualon the maker's product page |
| The site’s review | Sleipner (Side-Power) review |
Every published figure the site holds for the Sleipner SRP100 PRO, with where each came from.
Our notes from the manual and listings
In the box: Proportional: the joystick sets how hard it pushes. The power controller (PPC) is included.
12 V
This retractable lives in a housing let into the hull through a large opening, and drops when used. It is a bigger yard job than a tunnel. It also has a mechanism to keep in order. The SR100 with speed control (PRO).
Where each point above comes from
- Sleipner sells it for either end, so it can go at the bow or the stern.The maker's listing
- It is sold at 12 V and at 24 V.The maker's and dealers' listings
- Sleipner also prints a second, lower thrust figure for when the battery sags under load: 220 lb at 10.5 V.The maker's published rating
- The boat comes out of the water to install it: it needs a large hull opening below the waterline.The mounting: a bore through the hull, or a housing recessed into it
- No US dollar price is published for it, so we can work out no installed cost.The maker and the dealers the database reads
Not sure this is the one? The thruster finder asks about your boat and prices every unit that fits.